Circlips and Retaining Rings Index
E Type Circlips N1500 incorporating BS 3673 part 2 and MIL-R-21248/MS 16633
The most common form of radially fitted circlips for shafts with grooves. Provide a large shoulder on a relatively small shaft diameter. This range can be supplied stacked on rods for use with applicators and dispensers for rapid installation, thus resulting in sharply reduced assembly costs. Only the groove size is critical with this type of circlip, the shaft diameter can be varied widely.
Standard material: Carbon Spring Steel - Standard Finish: Phosphate and Oil.
(Also available in Stainless Steel)
| Please prefix code numbers with N1500/* This size in Beryllium Copper only | Measurements in inches & lb.f | ||||||||||||||
| Key to table headings and abbreviations | |||||||||||||||
| Shaft | Circlip Dimensions | Groove Dimensions | Code No. |
||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S | Tol | t | Tol | D | C | A | Tol | Fr lb.f |
G | Tol | W | n | Fr lb.f |
||
| .040 | +.010 -.000 |
.010 | ±.001 | .079 | .090 | .025 | +.001 -.003 |
15 | .026 | +.002 -.000 |
.012 | .014 | 5 | *X004 | |
| .062 | +.030 -.000 |
.010 | .140 | .150 | .051 | 36 | .052 | .012 | .010 | 6 | X006 | ||||
| .062 | .010 | .156 | .165 | .051 | 36 | .052 | .012 | .010 | 6 | 0006 | |||||
| .062 | .020 | ±.002 | .187 | .200 | .051 | 72 | .052 | .023 | .010 | 6 | Y006 | ||||
| .094 | .015 | .230 | .245 | .069 | ±.002 | 81 | .074 | .018 | .020 | 17 | X009 | ||||
| .094 | .015 | .187 | .200 | .073 | +.001 -.003 |
81 | .074 | .018 | .020 | 17 | 0009 | ||||
| .110 | .015 | .375 | .390 | .076 | 95 | .079 | .018 | .030 | 32 | X011 | |||||
| .125 | +.040 -.000 |
.015 | .230 | .240 | .094 | 108 | .095 | .018 | .030 | 35 | 0012 | ||||
| .140 | .015 | .203 | .214 | .100 | 121 | .102 | .018 | .038 | 50 | X014 | |||||
| .140 | .015 | .250 | .265 | .108 | 121 | .110 | .018 | .030 | 39 | Y014 | |||||
| .140 | .025 | .270 | .285 | .102 | 202 | .105 | .029 | .034 | 46 | 0014 | |||||
| .156 | +.050 -.000 |
.025 | .282 | .295 | .114 | 225 | .116 | .029 | .040 | 58 | 0015 | ||||
| .172 | .025 | .312 | .325 | .125 | 248 | .127 | .029 | .044 | 72 | X017 | |||||
| .188 | +.060 -.000 |
.025 | .375 | .390 | .122 | 271 | .125 | .029 | .062 | 110 | X018 | ||||
| .188 | .025 | .335 | .350 | .145 | 271 | .147 | .029 | .040 | 72 | 0018 | |||||
| .219 | +.100 -.000 |
.025 | .437 | .450 | .185 | 316 | .188 | .029 | .030 | 63 | X021 | ||||
| .250 | .025 | .527 | .540 | .207 | 361 | .210 | +.003 -.000 |
.029 | .040 | 93 | 0025 | ||||
| .312 | .025 | .500 | .520 | .243 | +.002 -.004 |
450 | .250 | .029 | .062 | 180 | X031 | ||||
| .375 | .035 | .660 | .680 | .300 | 757 | .303 | .039 | .072 | 252 | 0037 | |||||
| .438 | .035 | .687 | .710 | .337 | 885 | .343 | .039 | .094 | 388 | 0043 | |||||
| .438 | .035 | .600 | .620 | .375 | 884 | .380 | .039 | .058 | 237 | X043 | |||||
| .500 | +.120 -.000 |
.042 | .800 | .820 | .392 | 1210 | .396 | .046 | .104 | 485 | 0050 | ||||
| .625 | .042 | .940 | .960 | .480 | +.003 -.005 |
1510 | .485 | .046 | .140 | 816 | 0062 | ||||
| .744 | .050 | 1.000 | 1.020 | .616 | 2160 | .625 | .056 | .118 | 1190 | X074 | |||||
| .750 | .050 | 1.120 | 1.140 | .574 | 2520 | .580 | .056 | .170 | 1630 | 0075 | |||||
| .875 | .050 | 1.300 | 1.320 | .668 | 2840 | .675 | .056 | .200 | 1370 | 0087 | |||||
| .984 | .050 | 1.500 | 1.530 | .822 | 4250 | .835 | .056 | .148 | 1210 | X098 | |||||
| 1.188 | +.200 -.000 |
.062 | ±.003 | 1.626 | 1.670 | 1.066 | +.006 -.010 |
4920 | 1.079 | +.005 -.000 |
.068 | .108 | 1860 | X118 | |
| 1.375 | .062 | 1.875 | 1.920 | 1.213 | 4920 | 1.230 | .068 | .144 | 1860 | X137 | |||||
Circlips and Retaining Rings Index | Contact Springmasters with your specifications.
